The Nessmuk Challenge
-
I liked setting up the Paiute.

It seemed a little too fiddly to start with that one. The Y Bone is essentially a Paiute with a Y. It is easier to set up, but once done, it is a Paiute. There is a reason the Paiute is more popular than the Figure Four. -

Well, let's see what we have here.
-Spring-loaded snare
-Figure Four
-Promontory Peg
-Y Bone (Paiute variation)
-PaiuteSnare
All are deadfall traps except the snare, so the snare is either the best or the worst. I'd say that you'd want to be more particular about where you set the snare. Not that you should set up the deadfalls anywhere, but you could. Considering the fact that you need two cords for this, and a suitable spring-pole, and a game-trail to set it in, I'd say that this is not the easiest to set up.For the deadfalls, the Promontory Peg would be the easiest to set up. Find a stick, saw two opposite cuts, and snap it in two. Clean up the cut a little, find any toggle to tie the cord, and you're done.
The Figure Four takes a lot of fiddly carving to get right, in addition to being mindful of the length of the sticks.
The Paiute and Y Bone would be better than the Figure Four, I'd say. Easier to set up, and more reliable to trigger and get you dinner. The Y Bone takes a lot more carving than the Paiute but is much more stable thanks to the Y, which also makes it extremely easy to set up.So, in order of easiest to hardest, it would be
-Promontory Peg
-Y Bone
-Paiute
-Figure Four
-Snare

-
Day 27

Get the Ranger to pose while taking a stroll, I don't know why but there are really more than usual amount of people hiking the trails. I'd love to post with my axe and fixed blade more, but not with dozens of people watching over my shoulder.
-
Day 26:

The FX awl--which looks like it needs to be cleaned up a bit--used to open a parcel!

-

Get the Ranger to pose while taking a stroll, I don't know why but there are really more than usual amount of people hiking the trails. I'd love to post with my axe and fixed blade more, but not with dozens of people watching over my shoulder.
Lovely pic comis

Sent fra min FRD-L09 via Tapatalk
-
Nice work everyone
Day 26 more tyre fun

-
:ahhh Stop running over knives!!! :ahhh
-
Day 26
It is another gray and dreary day. Only the Chamber of Commerce still calls this "Sunny South Florida."

Here's the Spirit and the Little Black Talon with a cup of coffee.
-
Slow day for me, too.

-
Day 26
-
Nothing much. Except, I forgot, my grandmother put wood screws in the feed box lid to keep the bear from getting in it.
Thus, I had to remove and reinstall the screw
The right side didn't have a screw in where it should have been, so I relocated it. 91mm don't look that tough, but it took the job really well. I actually blew apart a current-production Antonini 100mm Farmer's Knife clone doing this job 2-3 years ago. Been meaning to redo the pins and wood handles for some time now. Really need to get at it. I'm going with a domed head over the "bird's eye" for strength.
<a href="https://flic.kr/p/2jLzAGP" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50387595631_2aa3d6a6c4_b.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>KIMG2314 by cody6268, on Flickr
-
Day 27
Third attempt at the bowdrill fire.
I have made some further improvements. Or so I thought.
The bearing block and spindle were a perfect fit, with a nub and hole. This was not ideal. The nub wore away, and the spindle had too much friction against the bearing block. To counter this, I tapered the spindle to fit into a cap nut. It was a little too thin to withstand the pressure, and it snapped after twenty seconds. It had very little friction and I got smoke, so it is not bad. If the cap nut was a little wider, the spindle point would have been more robust.I also scored grooves along the length of the spindle, to make the cord bite into it. My spindle was a polished broom handle, so it was quite smooth. I scraped it with my Mora's spine, but it was still smooth enough not to move some times when pressing down on it and working the bow. Scoring along the length of the spindle helped, but not that much. Spinning made the cord compress the grooves, which made the spindle smooth again. The cord is also not that rough, so I may need to replace that as well.
I put a steel wire loop in the middle of the bow to hold the spindle in place. It makes it easier to get in position without fumbling to get everything together.
The cap nut idea has some merit, so I am not done with it. I have to re-tighten the cord and score the spindle along its length again.

I also found another car seat clip with some seat belt length.


-
-
Day 18:
Rinaldi wants to go home after some standing block chop practise:

Sent from my iPhone using Tapatalk
-
Day 27

Enjoying a meal with family, can't help but to recruit the Ranger for cutting tasks. :D
-
Day 27:
Needed a new hole in my belt, Rebar to the rescue


Sent fra min FRD-L09 via Tapatalk
-
Sent fra min FRD-L09 via Tapatalk

Mousse is still loose! :D
@ReamerPunch said:
Day 27Third attempt at the bowdrill fire.
I have made some further improvements. Or so I thought.
The bearing block and spindle were a perfect fit, with a nub and hole. This was not ideal. The nub wore away, and the spindle had too much friction against the bearing block. To counter this, I tapered the spindle to fit into a cap nut. It was a little too thin to withstand the pressure, and it snapped after twenty seconds. It had very little friction and I got smoke, so it is not bad. If the cap nut was a little wider, the spindle point would have been more robust.I also scored grooves along the length of the spindle, to make the cord bite into it. My spindle was a polished broom handle, so it was quite smooth. I scraped it with my Mora's spine, but it was still smooth enough not to move some times when pressing down on it and working the bow. Scoring along the length of the spindle helped, but not that much. Spinning made the cord compress the grooves, which made the spindle smooth again. The cord is also not that rough, so I may need to replace that as well.
I put a steel wire loop in the middle of the bow to hold the spindle in place. It makes it easier to get in position without fumbling to get everything together.
The cap nut idea has some merit, so I am not done with it. I have to re-tighten the cord and score the spindle along its length again.

I also found another car seat clip with some seat belt length.


I think Nix's early suggestion of putting some lip stick/lube on top may help? Also, I have seen people wetting their bow string to create more friction, that could be worth a try too.
-
Needed a new hole in my belt, Rebar to the rescue


Sent fra min FRD-L09 via Tapatalk
Nice use, I sometimes use the awl from MT/SAK as a reamer more than the 'awl' function, since I worry they would have created a hole so wide that each subsequent holes maybe too far apart. I wonder do anyone use them for leatherwork or only for emergency repair only.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
:D


