The Nessmuk Challenge
-
:ahhh Chili! :ahhh
-
Day 21 B
I put some Orzo pasta in this pot of Chili instead of beans. :o Needed a little change up. :D
-
Looks good. Orzo sounds great!

-
Day 21: nothing much again.
<a href="https://flic.kr/p/2jJXCzb" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50369261388_0f4c29ef20_b.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>KIMG2225 by cody6268, on Flickr
-
Day 22
Well, I finally tried the bow drill. I've seen tons of people do this on youtube and they make it look easy. It is not. I made too many mistakes.
Some tips if you ever try this:
Bearing block
-It needs to be a little thick. It will get very hot, too hot if it is thin.
-Glass has little friction, but if the spindle is too loose in there, it will wobble and be unstable.
-It needs to be comfortable. A tiny bearing block will not work. Get something that fills your palm.
-The less friction it has against the spindle the better.Spindle
-Ideally straight, soft wood.
-Carve the bearing block end into an acute point, to reduce friction.
-Carve the hearth board end into a blunt point. It has to engage into the hearth board and stay there.
-The points should be inline with the center axis of the body, as straight as you can make them.
-If your spindle escapes while spinning, do not touch either end. They will be hot.
-Rough up the length of it, so that the cord bites into it and actually spins it.Bow
-A Y at the end helps to hold the cord.
-Do not over-tighten the cord. Your spindle may shoot into orbit if you let it go.Hearth
-The divot you have to make for the spindle can be surprisingly small. As long as the spindle has a tiny, blunt point, a tiny divot will do.
-Allow for some space at the side of the divot. If the spindle drills too close to the edge, it may break loose and destroy the hearth board.I did not have a good enough bearing block to give this a proper try. I will have to make one. The tiny Nutella jar was not ideal.


-
Day 22:
Moar parts


Sent fra min FRD-L09 via Tapatalk
-
Quick lunchtime Nessmuking. Fried eggs and chicken on the menu. Used the gas grill, but whilst waiting, decided to see how long it would take to start a fire with SwissChamp, ferro rod and some dryer lint.
From this:

To this:

..in about 40 seconds. I think that with some kindle and wood that could’ve been nurtured into a proper fire quite easilySent from my iPhone using Tapatalk
-
@Borg said:
Thinking about how easy it would be to add a saw blade to your kit i decided to have a go at making a simple frame saw using just my 3 tools, the blade weighs nothing and could easily be carried rolled up inside a tin or something or as comis's video shows wrapped round your waist in the loops, on site it's easy enough to make the saw parts provided you find decent wood to work with, i'm good for that so i went with Hazel, there are a million ways to make this type of saw but i went with the basic rustic style, i could also have just used one piece of wood bent over like a bow saw, the tension would have held the blade fine, i will try that way the next time.All parts needed, cut with axe and the fixie as a sort of drill to make the holes for the crossbar and to make the slits needed for the blade, folder was pressed into service for the cord grooves and the small pegs to hold the blade on

And put together, it works


One of my uprights was a bit gnarly so i would use a nice straight piece next time, the holes and pointed crossbar was the thing that took the time here, they have to be right, i took it apart a few times to fettle it but got there in the end, took me about half an hour all in but i wasn't in a rush, with experience you could probably get that down to 10 mins or so, less if you were allowed to use the saw :D
Another thought i had was if i was moving camp i would leave the wood behind and make new ones on the new site, i would carry the blade, the cord and probably the two small pegs holding the blade on as they took a while to make, the rest i would burn and heat my coffee on the fire
that is of course if i was sure the new site had trees...
Edited to add, Day 21Nice job on the frame saw !
-
@ReamerPunch said:
Well, I finally tried the bow drill. I've seen tons of people do this on youtube and they make it look easy. It is not. I made too many mistakes.
It is definitely not as straight forward as they make it look on TV! Great attempt, though.

-
Day 22:

-
It is definitely not as straight forward as they make it look on TV! Great attempt, though.

I need an actual bearing block. I thought the tiny Nutella jar, being glass, would be ok, but the spindle did not sit well inside. It kept wobbling too much, and since the divot is shallow, the spindle kept jumping out.
I'll make a bearing block and try again.
-
@Borg said:
Thinking about how easy it would be to add a saw blade to your kit i decided to have a go at making a simple frame saw using just my 3 tools, the blade weighs nothing and could easily be carried rolled up inside a tin or something or as comis's video shows wrapped round your waist in the loops, on site it's easy enough to make the saw parts provided you find decent wood to work with, i'm good for that so i went with Hazel, there are a million ways to make this type of saw but i went with the basic rustic style, i could also have just used one piece of wood bent over like a bow saw, the tension would have held the blade fine, i will try that way the next time.All parts needed, cut with axe and the fixie as a sort of drill to make the holes for the crossbar and to make the slits needed for the blade, folder was pressed into service for the cord grooves and the small pegs to hold the blade on

And put together, it works


One of my uprights was a bit gnarly so i would use a nice straight piece next time, the holes and pointed crossbar was the thing that took the time here, they have to be right, i took it apart a few times to fettle it but got there in the end, took me about half an hour all in but i wasn't in a rush, with experience you could probably get that down to 10 mins or so, less if you were allowed to use the saw :D
Another thought i had was if i was moving camp i would leave the wood behind and make new ones on the new site, i would carry the blade, the cord and probably the two small pegs holding the blade on as they took a while to make, the rest i would burn and heat my coffee on the fire
that is of course if i was sure the new site had trees...
Edited to add, Day 21That is fantastic adaptation!

@Alan K. said:
Great work on the saw Borg. Did you try it out after you put it together?
Comis, Cast Iron cookware is not recommended for some types of stove tops such as the seamless ceramic cooktops. It may damage them from the weight. However, using them is easy on a grill, over a fire, or even in the oven. The cast iron is easy enough to care for. You never put it on the fire empty it has to at least have some cooking oil in it. When you clean it you can use soap and water but it must then be completely dried or it will rust, and when it is dry you should put it back on the heat and coat it, inside and out, with cooking oil while it is warm before you put it away. The coating of oil on the outside just prevents rust, but the coat of oil on the inside is seasoning it and helping it to become a non-stick surface when you cook in it.Alan, thank for the great tips!
I am on a look out for one. Just having a hard time deciding one with legs or without, but since my chance going car camping is few and far in between. I probably lean towards one without. Shipping is another huge issue, but hopefully I could figure something out eventually.What Alan said.
If you are not going to use your Dutch Oven on the fire or coals, you might consider trying an enameled cast iron Dutch Oven. Even easier to care for, and they don't mind having acidic foods simmer away for hours.
Just be sure it can go in the oven! Some models have plastic handles that will melt in the oven. Wha...?

I keep looking at one of Lodge's enameled cast iron pots:

I think these type of cookware is more easier to get than the traditional ones(since the outdoor scene is really lame where I live), now if I could convince Mrs to make something with it...

-
Mrs Nix wanted to get a little nature time today. I packed a small rucksack and we headed out to a local park with Adventure Boy.
After a nice walk by the lake....

We settled down for a breakfast of Builder's Tea and homemade granola bars:

There had been two granola bars present right before I took the snap.......

Lovely views, and we saw a number of birds--Blue birds, Goldfinches, Swallows, Magpies, and Grouse. You can see on the rock in this shot a small with speck, that's a Sea Gull!

Adventure Boy loved the outing, but was a little annoyed by some restrictions.....

Still, we were all glad to get out for a leisurely walk and lakeside breakfast!


Say.....that looks like an area to go camping.......hmmmmm....
The last picture totally draws me in....imagine a sunrise or sunset there.

After Moose and I got back from hiking. I put Moose to work chopping up Romanian Red Garlic and Serrano Chili's for the Challenge Chili. :D
I put some Orzo pasta in this pot of Chili instead of beans. :o Needed a little change up. :D
Nothing beats a good meal after a good hike!
@ReamerPunch said:
Day 22Well, I finally tried the bow drill. I've seen tons of people do this on youtube and they make it look easy. It is not. I made too many mistakes.
Some tips if you ever try this:
Bearing block
-It needs to be a little thick. It will get very hot, too hot if it is thin.
-Glass has little friction, but if the spindle is too loose in there, it will wobble and be unstable.
-It needs to be comfortable. A tiny bearing block will not work. Get something that fills your palm.
-The less friction it has against the spindle the better.Spindle
-Ideally straight, soft wood.
-Carve the bearing block end into an acute point, to reduce friction.
-Carve the hearth board end into a blunt point. It has to engage into the hearth board and stay there.
-The points should be inline with the center axis of the body, as straight as you can make them.
-If your spindle escapes while spinning, do not touch either end. They will be hot.
-Rough up the length of it, so that the cord bites into it and actually spins it.Bow
-A Y at the end helps to hold the cord.
-Do not over-tighten the cord. Your spindle may shoot into orbit if you let it go.Hearth
-The divot you have to make for the spindle can be surprisingly small. As long as the spindle has a tiny, blunt point, a tiny divot will do.
-Allow for some space at the side of the divot. If the spindle drills too close to the edge, it may break loose and destroy the hearth board.I did not have a good enough bearing block to give this a proper try. I will have to make one. The tiny Nutella jar was not ideal.


Great job trying!
I only tried the friction fire long, long time ago, but did remember it really worked muscles that I didn't even know I have. That experience alone is a constant reminder that I must, must, must have a lighter or at least a ferro rod with me for fire starting.
Are we going to see chapstick fire or candle? This trip is something to look forward to!

-
Day 22

JG5 was busy helping me pack. Hopefully I will be able to sneak out in between meetings to ship out the first batch of them. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



