The Nessmuk Challenge
-
@ReamerPunch said:
Well, I finally tried the bow drill. I've seen tons of people do this on youtube and they make it look easy. It is not. I made too many mistakes.
It is definitely not as straight forward as they make it look on TV! Great attempt, though.

-
Day 22:

-
It is definitely not as straight forward as they make it look on TV! Great attempt, though.

I need an actual bearing block. I thought the tiny Nutella jar, being glass, would be ok, but the spindle did not sit well inside. It kept wobbling too much, and since the divot is shallow, the spindle kept jumping out.
I'll make a bearing block and try again.
-
@Borg said:
Thinking about how easy it would be to add a saw blade to your kit i decided to have a go at making a simple frame saw using just my 3 tools, the blade weighs nothing and could easily be carried rolled up inside a tin or something or as comis's video shows wrapped round your waist in the loops, on site it's easy enough to make the saw parts provided you find decent wood to work with, i'm good for that so i went with Hazel, there are a million ways to make this type of saw but i went with the basic rustic style, i could also have just used one piece of wood bent over like a bow saw, the tension would have held the blade fine, i will try that way the next time.All parts needed, cut with axe and the fixie as a sort of drill to make the holes for the crossbar and to make the slits needed for the blade, folder was pressed into service for the cord grooves and the small pegs to hold the blade on

And put together, it works


One of my uprights was a bit gnarly so i would use a nice straight piece next time, the holes and pointed crossbar was the thing that took the time here, they have to be right, i took it apart a few times to fettle it but got there in the end, took me about half an hour all in but i wasn't in a rush, with experience you could probably get that down to 10 mins or so, less if you were allowed to use the saw :D
Another thought i had was if i was moving camp i would leave the wood behind and make new ones on the new site, i would carry the blade, the cord and probably the two small pegs holding the blade on as they took a while to make, the rest i would burn and heat my coffee on the fire
that is of course if i was sure the new site had trees...
Edited to add, Day 21That is fantastic adaptation!

@Alan K. said:
Great work on the saw Borg. Did you try it out after you put it together?
Comis, Cast Iron cookware is not recommended for some types of stove tops such as the seamless ceramic cooktops. It may damage them from the weight. However, using them is easy on a grill, over a fire, or even in the oven. The cast iron is easy enough to care for. You never put it on the fire empty it has to at least have some cooking oil in it. When you clean it you can use soap and water but it must then be completely dried or it will rust, and when it is dry you should put it back on the heat and coat it, inside and out, with cooking oil while it is warm before you put it away. The coating of oil on the outside just prevents rust, but the coat of oil on the inside is seasoning it and helping it to become a non-stick surface when you cook in it.Alan, thank for the great tips!
I am on a look out for one. Just having a hard time deciding one with legs or without, but since my chance going car camping is few and far in between. I probably lean towards one without. Shipping is another huge issue, but hopefully I could figure something out eventually.What Alan said.
If you are not going to use your Dutch Oven on the fire or coals, you might consider trying an enameled cast iron Dutch Oven. Even easier to care for, and they don't mind having acidic foods simmer away for hours.
Just be sure it can go in the oven! Some models have plastic handles that will melt in the oven. Wha...?

I keep looking at one of Lodge's enameled cast iron pots:

I think these type of cookware is more easier to get than the traditional ones(since the outdoor scene is really lame where I live), now if I could convince Mrs to make something with it...

-
Mrs Nix wanted to get a little nature time today. I packed a small rucksack and we headed out to a local park with Adventure Boy.
After a nice walk by the lake....

We settled down for a breakfast of Builder's Tea and homemade granola bars:

There had been two granola bars present right before I took the snap.......

Lovely views, and we saw a number of birds--Blue birds, Goldfinches, Swallows, Magpies, and Grouse. You can see on the rock in this shot a small with speck, that's a Sea Gull!

Adventure Boy loved the outing, but was a little annoyed by some restrictions.....

Still, we were all glad to get out for a leisurely walk and lakeside breakfast!


Say.....that looks like an area to go camping.......hmmmmm....
The last picture totally draws me in....imagine a sunrise or sunset there.

After Moose and I got back from hiking. I put Moose to work chopping up Romanian Red Garlic and Serrano Chili's for the Challenge Chili. :D
I put some Orzo pasta in this pot of Chili instead of beans. :o Needed a little change up. :D
Nothing beats a good meal after a good hike!
@ReamerPunch said:
Day 22Well, I finally tried the bow drill. I've seen tons of people do this on youtube and they make it look easy. It is not. I made too many mistakes.
Some tips if you ever try this:
Bearing block
-It needs to be a little thick. It will get very hot, too hot if it is thin.
-Glass has little friction, but if the spindle is too loose in there, it will wobble and be unstable.
-It needs to be comfortable. A tiny bearing block will not work. Get something that fills your palm.
-The less friction it has against the spindle the better.Spindle
-Ideally straight, soft wood.
-Carve the bearing block end into an acute point, to reduce friction.
-Carve the hearth board end into a blunt point. It has to engage into the hearth board and stay there.
-The points should be inline with the center axis of the body, as straight as you can make them.
-If your spindle escapes while spinning, do not touch either end. They will be hot.
-Rough up the length of it, so that the cord bites into it and actually spins it.Bow
-A Y at the end helps to hold the cord.
-Do not over-tighten the cord. Your spindle may shoot into orbit if you let it go.Hearth
-The divot you have to make for the spindle can be surprisingly small. As long as the spindle has a tiny, blunt point, a tiny divot will do.
-Allow for some space at the side of the divot. If the spindle drills too close to the edge, it may break loose and destroy the hearth board.I did not have a good enough bearing block to give this a proper try. I will have to make one. The tiny Nutella jar was not ideal.


Great job trying!
I only tried the friction fire long, long time ago, but did remember it really worked muscles that I didn't even know I have. That experience alone is a constant reminder that I must, must, must have a lighter or at least a ferro rod with me for fire starting.
Are we going to see chapstick fire or candle? This trip is something to look forward to!

-
Day 22

JG5 was busy helping me pack. Hopefully I will be able to sneak out in between meetings to ship out the first batch of them. :D
-
Thanks again Comis for making the magnets for us. I had chili last night, and of course I forgot to take any pictures. Made mine with black beans instead of red because that's what was in the house. Never thought of using orzo before. It looks good.
-
@Alan K. said:
Great work on the saw Borg. Did you try it out after you put it together?Yes it worked fine, it was a bit shoogly at first but once the tension was ramped up it sorted itself out, the big letdown was the old blade i used, it really needs a sharpen and re set, a sharp new one would be better

@RF52 said:
Nicely done
I'm gonna try one myself someday 
Sent fra min FRD-L09 via Tapatalk
You would probably get it more stable with a tenon type joint but that takes more time and i wouldn't want to do that more than once so i'm thinking the less time you spend on it the less likely you are to want to carry the pieces with you if you move camp, if you are happy to carry the extra weight then it's worth doing neatly with more secure joints, the hole and pointy stick method i used works fine though, not pretty but it works

@Nix said:
Awesome!
I've been meaning to try that at some point.
Go for it, it makes a far better saw than one of those emergency chainsaw things, probably the same weight too

@ReamerPunch said:
Excellent project, Borg! It looks fantastic!
I don't have any blades like that, but once I do I'll make one of those too.
Thanks RP, i think every one you make will be quicker than the last and can soon rattle one out in no time

Thanks Steve


-
Day 22
I used the Spirit to skin an Amazon Brown. My prize today was new face masks and some stainless mesh. I'm going to cut the mesh to size to fit in the compartments of the silverware bin in my dishwasher because there are holes where knives and heavy utensils have poked through the plastic. I wish I'd thought of it sooner. The holes have been there for a couple of years already. -
Day 22
Today i tried a different method of making the saw

The blade is held in with pins slotted through and held in a groove

It works, plenty tension there to hold the blade tight, or should that be too much tension...

Even with the broken spine it still works and still holds as its just the cambium split but i wouldn't trust it for long
I will call this a fail even though its usable as it is, did Nessmuk carry duct tape?

Different species or a nicer stick called for i think
-
@old Lefty said:
Quick lunchtime Nessmuking. Fried eggs and chicken on the menu. Used the gas grill, but whilst waiting, decided to see how long it would take to start a fire with SwissChamp, ferro rod and some dryer lint.Lint is really good at getting it going, half a spark and its away, works well with Birch bark too

@ReamerPunch said:
Day 22Well, I finally tried the bow drill. I've seen tons of people do this on youtube and they make it look easy. It is not. I made too many mistakes.
Some tips if you ever try this:
Bearing block
-It needs to be a little thick. It will get very hot, too hot if it is thin.
-Glass has little friction, but if the spindle is too loose in there, it will wobble and be unstable.
-It needs to be comfortable. A tiny bearing block will not work. Get something that fills your palm.
-The less friction it has against the spindle the better.Spindle
-Ideally straight, soft wood.
-Carve the bearing block end into an acute point, to reduce friction.
-Carve the hearth board end into a blunt point. It has to engage into the hearth board and stay there.
-The points should be inline with the center axis of the body, as straight as you can make them.
-If your spindle escapes while spinning, do not touch either end. They will be hot.
-Rough up the length of it, so that the cord bites into it and actually spins it.Bow
-A Y at the end helps to hold the cord.
-Do not over-tighten the cord. Your spindle may shoot into orbit if you let it go.Hearth
-The divot you have to make for the spindle can be surprisingly small. As long as the spindle has a tiny, blunt point, a tiny divot will do.
-Allow for some space at the side of the divot. If the spindle drills too close to the edge, it may break loose and destroy the hearth board.I did not have a good enough bearing block to give this a proper try. I will have to make one. The tiny Nutella jar was not ideal.
Nice work, there's no point me even trying that here, too wet but i bet its a fantastic feeling when she fires

-
@Borg said:
Yes it worked fine, it was a bit shoogly at first but once the tension was ramped up it sorted itself out, the big letdown was the old blade i used, it really needs a sharpen and re set, a sharp new one would be better
You would probably get it more stable with a tenon type joint but that takes more time and i wouldn't want to do that more than once so i'm thinking the less time you spend on it the less likely you are to want to carry the pieces with you if you move camp, if you are happy to carry the extra weight then it's worth doing neatly with more secure joints, the hole and pointy stick method i used works fine though, not pretty but it works

Go for it, it makes a far better saw than one of those emergency chainsaw things, probably the same weight too

Thanks RP, i think every one you make will be quicker than the last and can soon rattle one out in no time

Thanks Steve


Good point in not complicating the build, spend to much time and you will be carrying all the parts.
Sent fra min FRD-L09 via Tapatalk
-
Day 22
The smoky skies finally cleared out yesterday afternoon. Now its cool overcast and drizzling. Every thing is wet. If I needed a fire I would resort to ferro rod and vaseline soaked cotton balls and maybe a storm match. :D
-
Day 22:
Today, scissors twice, both blades (opened mail and packages), and awl. The little SwissTech tool was used instead for drivers because they are machined, probably tool steel, and sharp. I mostly have it for pliers so I don't have to drag along full pliers or another multitool loaded down with redundancy.
Tried to repair hole to ensure my Granddad's hearing aid was (sort of) water resistant. Really need to drop the thing off at the hearing aid place to get rebuilt. I don't know who at Starkey thought acrylic like on a cheap lapel pin case on a several-hundred-dollar hearing aid was a good idea. I don't know why anyone would need to see the guts anyway. Yet LEGO uses polycarbonate on ten-cent bricks that is near indestructible. Heck, $3 safety glasses are polycarbonate, have protected me from some serious screw-ups and were still intact and have considerably more plastic.
<a href="https://flic.kr/p/2jKhWG5" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50373029468_f5940497c1_b.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>KIMG2226 by cody6268, on Flickr
Fixed my new glasses. Somehow they got knocked off my bed, and a lens fell out. I just now started carrying the eyeglass screwdriver, after finding one I didn't lose. Need to buy about a dozen of them. This one tool is why I converted to corkscrew.
<a href="https://flic.kr/p/2jKhWEB" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50373029383_5a9a9ecb1b_b.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>KIMG2227 by cody6268, on Flickr
Installed new indoor/outdoor thermometer outdoor transmitter. I first used the awl and SwissTech tool to drill the hole, then used a self-drilling wood screw to go the rest of the way. The screw head would not fit the notch for a nail/screw on the back, so I grabbed my hammer put a nail from a photo hanging kit in the hole--that fit perfectly. Also cut open the packaging (box, not clam pack, as this was bought online) with the pen blade. I need to really retire this hammer. It's an old Belknap Hardware that probably dates to the time of Nessmuk. It was my Great-Granddad's. It's fairly small, about 16 ounces, but for household stuff, it's all the hammer I need. I have a 28 oz. Estwing for the big stuff, 28 ounce Vaughan in my regular toolbox, and another 28 ounce Pittsburgh, a ripping hammer, which I mostly use for fencing since it is inexpensive to replace.
<a href="https://flic.kr/p/2jKmwdf" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50373727566_d4a243912b_b.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>KIMG2229 by cody6268, on Flickr
And a few other things I forgot--mostly mail and package opening with the blades.
-
Day 23
Having enjoyed the traps so far, I decided to make the Paiute deadfall, but I found this variation, the Y bone deadfall. Same concept as the paiute, but the Y gives it more stability. It worked like a charm.

Looking at it now, I have all the pieces required for the Paiute. I can use two sticks from the Figure Four, and the string and toggle from the Y bone.


I also shortened the long fishmouth spreader. I gave each arm half a coil, and now it is much stronger.



-
Nice work RP

Day 23:
Used the Rebar saw to cut of a piece of a wooden board to use as a backing for sandpaper to sharpen tools


Sent fra min FRD-L09 via Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


